Show us your honey!!

Josh · Post by **Josh** » Sat Dec 21, 2019 2:02 am

You know what time it is!

Sent from my LGMP260 using Tapatalk

Josh · Post by **Josh** » Sat Dec 21, 2019 5:08 am

GMO!!

Got a few questions for you big dawg

Every single time I do a bho run, I get a descent slab of shatter but there's always a couple spots that budder up.
Not that it's bad, but it makes me a little uneasy.
Other stuff is purging and that part prbly has butane left in it.....

My process- 1. freeze packed tube and butane

2. Blow into pyrex, which is sitting in another pan of hot water. 110-130 F

3. Pop bubbles until they slow and then scrape onto parchment.

4.place in vac chamber heated to 110-115 degrees

5. Pull low vacuum and release a few times until the muffin collapses, then pull 29.5 hg. Shut off vacuum. Wait for reaction to stop and flip the patty.

6. This is where things go bad

Pull full vacuum and reaction starts, budder spots appear and stop purging. Oil around it continues purging though

Pics incoming

Sent from my LGMP260 using Tapatalk

GMO · Post by **GMO** » Sat Dec 21, 2019 12:47 pm

integrajosh wrote: ↑
Sat Dec 21, 2019 5:08 am
and then scrape onto parchment.

thats your issue dude. smokey might has a link for you, but the disturbance of the scrap seems to cause buddering. a little earlier than scrap, maybe attempt a pour instead or even better, blast direct into some PTEF sheet formed into a bowl shape so you dont have to disturb the extract at all

also when you say pop bubbles, are you physically popping them or just watching. its a very hands off process imho buddy ;)

Josh · Post by **Josh** » Sat Dec 21, 2019 3:09 pm

GMO wrote:
integrajosh wrote: ↑
Sat Dec 21, 2019 5:08 am
and then scrape onto parchment.
thats your issue dude. smokey might has a link for you, but the disturbance of the scrap seems to cause buddering. a little earlier than scrap, maybe attempt a pour instead or even better, blast direct into some PTEF sheet formed into a bowl shape so you dont have to disturb the extract at all

also when you say pop bubbles, are you physically popping them or just watching. its a very hands off process imho buddy ;)

Ah ya you're prbly right bro!

By pop bubbles, I mean I just use my dab tool to get the bigger ones that take forever to pop. I'm kind of in a hurry between blasting and setting in the vac chamber
4 cats, a dog, and a gf with long hair....
You can imagine the contaminates in the air

Think my computer took a shit, I'll try one more time to upload

That ptfe looks awesome, some expensive shit though aye?!

Sent from my LGMP260 using Tapatalk

Josh · Post by **Josh** » Sat Dec 21, 2019 4:15 pm

Josh · Post by **Josh** » Sat Dec 21, 2019 4:16 pm

should I remove the budder spots and re-run them with my next batch you think?? I don't want to smoke butane

Smokey · Post by **Smokey** » Sat Dec 21, 2019 6:47 pm

How long was purge may i ask bro ??

Josh · Post by **Josh** » Sat Dec 21, 2019 8:07 pm

Smokey wrote:How long was purge may i ask bro ??

About 6 hours, flipped once after no more bubbles

Sent from my LGMP260 using Tapatalk

Smokey · Post by **Smokey** » Sat Dec 21, 2019 9:04 pm

integrajosh wrote: ↑
Sat Dec 21, 2019 8:07 pm

Smokey wrote:How long was purge may i ask bro ??
About 6 hours, flipped once after no more bubbles

Sent from my LGMP260 using Tapatalk

Dude, chuck her back in @ 36c, 25 psi for a further 12 hours

you don't need to ever pop any bubbles manually once shes in the chamber leave her there (maybe flip once), 6 hours purge is nothing bro honestly not for clean and stable glass, it's never too late