Welcome to the general & cannabis growers discussion section. This section is for general discussions about cannabis and growing. Plenty of laughs to be found in here. To become part of our online cannabis growing community click here to register.

Ecotechnics evolution fan controller

A place to discuss cannabis and growing related topics
User avatar
Minty
Registered User
Posts: 3893
Joined: Sat Apr 18, 2020 7:21 pm
Has thanked: 3802 times
Been thanked: 1494 times
Status: Offline

Re: Ecotechnics evolution fan controller

Post by Minty »

Thejokerjosh59 wrote:
Tue Jun 16, 2020 1:34 am
I’m guessing it’s similar tech to magnetic beaker spinners we use in the extract lab
That is exactly what I am trying to make to 'stir' my nutrients before I auto dose them.
Damn and I just purchased some plastic coated magnets (and they aint cheap!) - I bet you could have got me some old used ones ;o)

And as far as I know the stuff you are using is also NOT pwm based - but again -

:idn:
These users thanked the author Minty for the post (total 2):
Joker59 (Tue Jun 16, 2020 2:18 am) • Nom (Tue Jun 16, 2020 5:13 am)

Seed Stockers London Seed Centre The Cannabis Experts - You Tube Pheonix Seeds Invisible Sun LED Conscious gentics Barney's Farm Supernatural Seeds Tastebudz The Vault Cannabis Seed Store Philzon LED IZI Seeds IZI Seeds Tastebudz Breeders Colective Kaiju Nutrients Breeders Colective Kaiju Nutrients
User avatar
Minty
Registered User
Posts: 3893
Joined: Sat Apr 18, 2020 7:21 pm
Has thanked: 3802 times
Been thanked: 1494 times
Status: Offline

Re: Ecotechnics evolution fan controller

Post by Minty »

MrNice wrote:
Tue Jun 16, 2020 1:18 am
automation done for you in one easy step not cheap tho plus you can control heat all the nessary variables you need to control
I can already do all that and more with mine - got Air Conditioner support (Infra Red Sender) going in this weekend ;o)
Rather than adjust the voltages my current software just turns the heater on and off (depending on the sensors) - adjusting the actual heat from my heater would be so much more controllable if I could automate the wattage! and that is why this is interesting ;o) The ability of adjusting the voltage/current on the fly (think slow down the recirculating water pumps on demand) would be a game changer for me. Definitely going to be looking into what chips they are using in that...
These users thanked the author Minty for the post:
Nom (Tue Jun 16, 2020 5:13 am)

User avatar
Joker59
Registered User
Posts: 1134
Joined: Mon Jun 15, 2020 8:56 am
Location: In my fucking garden where I should be
Has thanked: 313 times
Been thanked: 377 times
Contact:
Status: Offline

Re: Ecotechnics evolution fan controller

Post by Joker59 »

Minty wrote:
Tue Jun 16, 2020 1:46 am
MrNice wrote:
Tue Jun 16, 2020 1:18 am
automation done for you in one easy step not cheap tho plus you can control heat all the nessary variables you need to control
I can already do all that and more with mine - got Air Conditioner support (Infra Red Sender) going in this weekend ;o)
Rather than adjust the voltages my current software just turns the heater on and off (depending on the sensors) - adjusting the actual heat from my heater would be so much more controllable if I could automate the wattage! and that is why this is interesting ;o) The ability of adjusting the voltage/current on the fly (think slow down the recirculating water pumps on demand) would be a game changer for me. Definitely going to be looking into what chips they are using in that...
Sounds like you have a killer set up. We had a similar set up with a sensor array and and a little automation for stuff like irrigation and temp. We are also hoping to go back with something a bit more programable. I don’t really make those decisions (buddies are a engineer and a industrial electrician) but the more I know the better lol hoping they don’t go to over board because the less we control the more I worry lol
These users thanked the author Joker59 for the post (total 2):
Nom (Tue Jun 16, 2020 5:13 am) • Minty (Tue Jun 16, 2020 12:19 pm)
Just a Canadian Cannabis enthusiast🇨🇦 If you aren’t learning then what’s the point!?
“You may be Galileo, but your probably just wrong! “
“I disapprove of what you say, but I will defend to the death your right to say it“ Evelyn Beatrice Hall.
viewtopic.php?f=88&t=6271 Purple Orange (CBD+), CBDurban, Gorilla Zkittles, And more!! IG@thekidchronnabis

User avatar
Nom
Registered User
Posts: 1826
Joined: Sun Nov 10, 2019 10:31 am
Location: Narnia
Has thanked: 635 times
Been thanked: 966 times
Status: Offline

Re: Ecotechnics evolution fan controller

Post by Nom »

Wow, thanks lads. I just wanted to know if it will make my ac fan hun if I use one. I'm currently using a voltage stepper but it hasnt got a temperature probe and I fancied something that could do a bit more. Thing is I cant be having any fan hum though and I'm trying to find a controller that fits the bill for my ac fans. I really should upgrade to an ec fan I know but one of those plus a controller with the functionality I want is gonna bend me over a little too much

User avatar
MrNice
Registered User
Posts: 10709
Joined: Fri Apr 24, 2020 7:25 pm
Has thanked: 4883 times
Been thanked: 6212 times
Status: Offline

Re: Ecotechnics evolution fan controller

Post by MrNice »

Nomoli it will humm at low speeds gmo has one ask him about humming
all electronic speed controllers humm Id stick with what you have and adapt it
Image

Post Reply

Return to “General Growers & Cannabis Discussion”