999 I need a sparky!

[Mafooo]

Same shit on our end. Needed a new fridge afterwards Cap...

[Inactive account]

I don’t even trust him to poke a wire in a hole

[Minty]

Okey cokey how the fuk do I wire this up? Because I'll be needing to do it soon and I wanna see its beam, Without setting my gaff on fire Ta.

What driver do you have Captain?

Basically the boards have a plus and a minus (which is duplicated on each end - you only need to use one of each of them - either end connections are for wiring convenience). The wiring mostly depends on what type of driver you have i.e. constant current or variable and how you want to wire the diodes i.e. Series or Parallel. Also where you want the power cord going to the wall coming out from the light ie top middle or bottom / reft, right middle can be an influence.

Simple examples of each and excuse me if these are wrong as had a few beers, but you should be looking at something like the following:-

If you want to feed the light from either end of the fitting:-



If you want to feed the light from the middle of the fitting:-




DOUBLE CHECK THIS SHIT AS IT DEPENDS ON WHICH DRIVER YOU HAVE!! and this is just an example.

Did it come with wire? I found the best wire to use is the solid 'Twin and Earth' e.g. 1.0mm T&E cable that is commonly used for wiring up houses as these are well rated are also solid cored as those connectors are push fit.

I wouldn't mess to much with them once you have the wire in (or before as they break easily but only the plastic 'disengage part' - the spring tension part holds well and if you need to get the wire out a gentles 'wiggle' while gently pulling will do the trick)


Don't do anything until we double check mate but in my experience they are fine if you do it wrong and will just not turn on (although this was NOT the constant current driver so advice will be different).

[Minty]

its easy captin

https://invisiblesunled.co.uk/pages/assembly

look down the page ISH265 is like the one you have cap little drawing showing how to wire the boards 240v side the one with 3 wires is like wiring a plug

Damn, Wish I had seen this before spending 20 mins drawing one... Cheers Nice.

[Captain Beefheart]

I don’t even trust him to poke a wire in a hole

hehehe aye aye

Okey cokey how the fuk do I wire this up? Because I'll be needing to do it soon and I wanna see its beam, Without setting my gaff on fire Ta.

What driver do you have Captain?

Basically the boards have a plus and a minus (which is duplicated on each end - you only need to use one of each of them - either end connections are for wiring convenience). The wiring mostly depends on what type of driver you have i.e. constant current or variable and how you want to wire the diodes i.e. Series or Parallel. Also where you want the power cord going to the wall coming out from the light ie top middle or bottom / reft, right middle can be an influence.

Simple examples of each and excuse me if these are wrong as had a few beers, but you should be looking at something like the following:-

If you want to feed the light from either end of the fitting:-



If you want to feed the light from the middle of the fitting:-




DOUBLE CHECK THIS SHIT AS IT DEPENDS ON WHICH DRIVER YOU HAVE!! and this is just an example.

Did it come with wire? I found the best wire to use is the solid 'Twin and Earth' e.g. 1.0mm T&E cable that is commonly used for wiring up houses as these are well rated are also solid cored as those connectors are push fit.

I wouldn't mess to much with them once you have the wire in (or before as they break easily but only the plastic 'disengage part' - the spring tension part holds well and if you need to get the wire out a gentles 'wiggle' while gently pulling will do the trick)


Don't do anything until we double check mate but in my experience they are fine if you do it wrong and will just not turn on (although this was NOT the constant current driver so advice will be different).

its easy captin

https://invisiblesunled.co.uk/pages/assembly

look down the page ISH265 is like the one you have cap little drawing showing how to wire the boards 240v side the one with 3 wires is like wiring a plug

Damn, Wish I had seen this before spending 20 mins drawing one... Cheers Nice.

fuk knows bach ewe just fried my head rite there ^^^^

[Captain Beefheart]

me + wires ach y fi......

[Captain Beefheart]

i`ll read the link in morning diolch yn fawr.

[Minty]

fuk knows bach ewe just fried my head rite there

Take a picture of what you received apart from the nice LED light mate? Did they include a driver for it?

[MrNice]

Invisible Sun LED ISH265 Pro quick assembly video
https://www.youtube.com/watch?time_cont ... e=emb_logo

MrNice rough ass drawing

[Minty]

Invisible Sun LED ISH265 Pro quick assembly video
https://www.youtube.com/watch?time_cont ... e=emb_logo

MrNice rough ass drawing

Spot on mate if it is a series driver?. We still need to confirm how is going to be driving this and if they even included a driver I think before Mrs Beef get's the screwdriver out and wires it up for him ;o)